8.7	Planning Structured Cabling: Cabling and Grounding
	8.7.1	Causes of ground potential problems
In order to understand the conditions that must be present in order for there to be a problem, assume that the ground wire for building A has a slightly different potential, to the common and hot wires, than the ground wire for building B. In this example, the outer casings of the computer devices in building A have a different potential from the outer casings of the computer equipment located in building B. If a circuit were established that linked the computer devices in building A to those in building B, then electrical current would flow from the negative source to the positive source. Theoretically, in such a situation, if someone were to touch network devices with different ground connections, they would receive a nasty shock. In the example outlined above, can you explain why a person would have to simultaneously touch devices with different grounds for a shock to occur? As this theoretical example demonstrates, when devices with different ground potentials are linked in a circuit, they can produce hazardous shocks. In the real world, however, the chances of any such occurrence as that described above, are very slight, because in most instances a person would have to have extremely long arms to complete the circuit. There are situations however, where such circuits can be created.

8.7	Planning Structured Cabling: Cabling and Grounding
	8.7.2	Networking devices and dangerous circuits
As illustrated in the previous example, the closed circuit produced by your body and the UTP cable would allow electrons to flow from the negative source to the positive source through your body. This is due to the ground wires for the devices in one location having a slightly different potential to both the common and hotwires than the ground wires for the devices in the second location. The closed circuit produced by the use of UTP cable would then allow electrical current to flow from the negative source to the positive source. Anyone touching the chassis of a device on the network would receive a nasty shock. A good way to avoid having current pass through the body, and through the heart, is to use the one hand rule. Simply put, this rule says that you should not use more than one hand at a time to touch any electrical device. The second hand should remain in your pocket.

8.7	Planning Structured Cabling: Cabling and Grounding
	8.7.3	Faulty ground wiring problems
When everything works correctly, according to IEEE standards, there should be no voltage difference between the networking media and the chassis of a networking device. This is because the standards separate LAN media connections from power connections. However, things don't always work as planned. For example, if there were a faulty ground wire connection to an outlet, there would be potentially fatal voltages between the LAN's UTP cabling and the chassis of a networking device. To understand the potential consequences of such a situation, imagine what would happen if you were to place your hand on the computer's case, while simultaneously touching an Ethernet connector. By touching both the computer's case and the Ethernet connector, your body, acting as a closed circuit, would allow electrons to flow from the negative source to the positive source. As a result, you could receive a painful shock.

8.7	Planning Structured Cabling: Cabling and Grounding
	8.7.4	Avoiding potentially dangerous circuits between buildings
TIA/EIA-568-A specifications for backbone cabling permit the use of fiber-optic cable, as well as UTP cable. Because glass is an insulator rather than a conductor, electricity does not travel over fiber-optic cables. Therefore, when multiple buildings are to be networked, it is highly desirable to use fiber-optic cable as the backbone.

8.7	Planning Structured Cabling: Cabling and Grounding
	8.7.5	How fiber optic cable can prevent electrical shocks
Most network installers today recommend the use of fiber-optic cable for backbone cabling to link wiring closets that are on different floors, of the same building, as well as between separate buildings. The reason for this is simple. It is not uncommon for floors of the same building to be fed by different power transformers. Different power transformers can have different earth grounds, thus causing the problems previously described. Non-conducting optical fibers eliminate the problem of different grounds

8.7	Planning Structured Cabling: Cabling and Grounding
	8.7.6	Reasons for using UTP for backbone cabling between buildings
While faulty wiring can present one type of electrical problem for a LAN that has UTP cable installed in a multi-building environment, there is another type of problem that can occur. Whenever copper is used for backbone cabling, it can provide a pathway for lighting strikes to enter a building. Such strikes are a common cause of damage to multi-building LANs. It is for this reason that new installations of this type are moving toward the use of fiber-optic cable for the backbone cabling.